| Age | Commit message (Collapse) | Author |
|---|
|
Since b57fb80a7d (init, clone: support --separate-git-dir for .git file)
git clone supports the --separate-git-dir option to create the git dir
outside the work tree. But when that option is used, the git dir won't be
deleted in case the clone fails like it would be without this option. This
makes clone lose its atomicity as in case of a failure a partly set up git
dir is left behind. A real world example where this leads to problems is
when "git submodule update" fails to clone a submodule and later calls to
"git submodule update" stumble over the partially set up git dir and try
to revive the submodule from there, which then fails with a not very user
friendly error message.
Fix that by updating the junk_git_dir variable (used to remember if and
what git dir should be removed in case of failure) to the new value given
with the --seperate-git-dir option. Also add a test for this to t5600 (and
while at it fix the former last test to not cd into a directory to test
for its existence but use "test -d" instead).
Reported-by: Manlio Perillo <manlio.perillo@gmail.com>
Signed-off-by: Jens Lehmann <Jens.Lehmann@web.de>
Signed-off-by: Junio C Hamano <gitster@pobox.com>
|
|
Converts tests between t3600-t6300.
Signed-off-by: Nanako Shiraishi <nanako3@lavabit.com>
Signed-off-by: Junio C Hamano <gitster@pobox.com>
|
|
This patch changes every occurrence of "! git" -- with the meaning
that a git call has to gracefully fail -- into "test_must_fail git".
This is useful to
- make sure the test does not fail because of a signal,
e.g. SIGSEGV, and
- advertise the use of "test_must_fail" for new tests.
Signed-off-by: Stephan Beyer <s-beyer@gmx.net>
Signed-off-by: Junio C Hamano <gitster@pobox.com>
|
|
Originally, test_expect_failure was designed to be the opposite
of test_expect_success, but this was a bad decision. Most tests
run a series of commands that leads to the single command that
needs to be tested, like this:
test_expect_{success,failure} 'test title' '
setup1 &&
setup2 &&
setup3 &&
what is to be tested
'
And expecting a failure exit from the whole sequence misses the
point of writing tests. Your setup$N that are supposed to
succeed may have failed without even reaching what you are
trying to test. The only valid use of test_expect_failure is to
check a trivial single command that is expected to fail, which
is a minority in tests of Porcelain-ish commands.
This large-ish patch rewrites all uses of test_expect_failure to
use test_expect_success and rewrites the condition of what is
tested, like this:
test_expect_success 'test title' '
setup1 &&
setup2 &&
setup3 &&
! this command should fail
'
test_expect_failure is redefined to serve as a reminder that
that test *should* succeed but due to a known breakage in git it
currently does not pass. So if git-foo command should create a
file 'bar' but you discovered a bug that it doesn't, you can
write a test like this:
test_expect_failure 'git-foo should create bar' '
rm -f bar &&
git foo &&
test -f bar
'
This construct acts similar to test_expect_success, but instead
of reporting "ok/FAIL" like test_expect_success does, the
outcome is reported as "FIXED/still broken".
Signed-off-by: Junio C Hamano <gitster@pobox.com>
|
|
Signed-off-by: Junio C Hamano <junkio@cox.net>
|
|
the repository argument for git-clone should be relative to $PWD
instead of the given target directory. The old behavior gave us
surprising success and you need a few minute to know why it worked.
GIT_DIR is already exported so no need to cd into $D. And this makes
$PWD for git-fetch-pack, which is the actual command to take the given
repository dir, the same as git-clone.
Signed-off-by: Yasushi SHOJI <yashi@atmark-techno.com>
Signed-off-by: Junio C Hamano <junkio@cox.net>
|
|
Signed-off-by: Carl Worth <cworth@cworth.org>
Signed-off-by: Junio C Hamano <junkio@cox.net>
|
